Raymarine RC400 – Pros and Cons

rc400 on bracketI was lucky enough to get a RC400 and a Garmin 76CS as gifts in August 2005.

There seems to be a number of discussions on various forums about the pros and cons of these units so I thought I would give my experiences of using both while sailing in the English Channel for the past 2 years.


RC400- the Pros:
1. I have limited space at the helm of my 32ft yacht so I have a mounted the RC400 there since there is no room for anything larger. This makes the RC400 a great choice and it fits well.

2. The colour screen is good and is legible even in pouring rain

3. The screen can be turned down at night and does not interfere with night vision like some of my friend’s larger consoles such as the Raymarine C80 and larger.RC400 1

4. I have installed a power cable and do not rely on the batteries while on passage.

5. I can see a high quality chart at the helm, without going below to see my main chart plotter which is the Raymarine C120 at the nav table.

6. It has its own GPS so it is another backup for position data separate from my main GPS / C120 setup.

7. The Navionics Gold chart is excellent and is compatible with the C120 unit I use at the nav table.

RC400- the Cons:
1. I agree with those who say that the unit eats batteries. The 2300mAh batteries hardly last 1 hour and mine no longer hold a charge. I have now bought 2500mAh batteries – but will still use it on power from the yacht while I am on passage.

2. Interfacing is useless. It does not interface using Seatalk so I cannot connect it to the C120. Although both the C120 and the RC400 have import/export functions for waypoint data – I have not been able to make this work by exporting from the C120 to a Sandisk and then importing to the RC400.

3. I have not tried interfacing with NMEA data since all my instruments are Raymarine and are outputting Seatalk as is the C120.

RC400 24. The batteries do expire rapidly. Apparently it is using current even when it is off. The original 2300mAH AA batteries are all dead now and won’t accept a charge. I have just bought 4 x 2500mAH batteries and a fast charger – so I will see how I get on with those. But to be honest – I have mains power connected to the RC400 at the helm so it is fine on passage and the built in battery charger keeps topping up the batteries while on passage.

5. The GPS seems to lose position at least once on passage – I have a feeling this is a glitch in the software or firmware since my other two GPS units never lose position. Turning the unit off and on seems to correct the issue.

6. Raymarine have discontinued this unit – so no more support. They must have their reasons.


10 thoughts on “Raymarine RC400 – Pros and Cons

  1. Pingback: marine gps chart plotter
  2. Thanks for the review. I know it’s a couple of years old now but I’m researching this type of product as part of my business so still very helpful.

  3. Does anyone know how to reset the unit. I do not have the manual. and stops on the home screen during boot up.

    1. Resetting the System
      Three types of reset are available for the Chartplotter:
      • Power-On Reset: When you turn the display unit off, then on again,
      the screen reverts to the chart display with all windows cleared.
      • Hardware Reset: This procedure enacts a power-on reset if the unit
      has entered a lock-up condition.
      To perform a hardware reset, press and hold the POWER key for 9
      • Factory Reset: This resets all values back to their original factory
      settings. The factory default settings are listed in Chapter 4.
      Note: Take care–factory reset clears all Waypoint and Route databases.
      To perform a factory reset:
      1. Power off the unit.
      2. Press and hold CLEAR while powering up until is displayed.
      3. Either press CLEAR to abort Factory Reset and resume normal
      Power-Up or press ENTER to continue Factory Reset.
      4. Press ENTER again; the unit restarts as for a first time Power Up
      with all values reset to their original factory settings.

  4. i tried the various resets. still stops on the raymarine home screen during boot up? any ideas.


    chartplotters by raymarine. Globe.

    Always stops on this screen.

    1. Rick

      Then the only thing left is the power source (other than canning it!)

      On page 12 of the manual you will see the following advice about batteries.

      “….When used portably, the RC400 can be powered by the supplied four (4)
      Nickel Metal Hydride (Ni-MH) batteries or with four (4) AA alkaline cells
      (not supplied), using the supplied Battery Tray.
      Note: The RC400 was designed to be used with all Ni-MH or all alkaline
      battery cells only. Do not mix or use any other battery types.
      ? To install batteries:
      1. Remove the battery tray as shown in Figure 2-2 .
      2. Locate the Battery Type switch on the inside of the chartplotter adjacent
      to the chart card (if already installed) and turn to the appropriate
      position: ALKALINE or RECHARGEABLE….”

      First make sure the battery type switch is set correctly:-)

      Secondly, I only use rechargeable NimH batteries AND I highly recommend uprating them to 4 x AA 2500mAh Ni-MH rechargeable batteries.
      See my posting here on the subject of batteries for portable items

      I do hope this helps :-/

  5. My rc400 has just started freezing up on globe logo screen on startup.
    Tried all of above. Looks like a bin job
    Unless anybody has other idea.
    Can run all the test sequences via page startup but still freezes.

Leave a Reply to boating forum Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.